|
|
|
Flexographic
Solvent Equipment
|
 |
Interflex
Washout Units
|
|
| |
|
Features
|
|
- The
Interflex Washout Units produces touch-dry
flexograpic photopolymer plates
- The
plates are washed out upside down. This patented
design allows solvent quantity control, automatic
relief adjustment and reduced plate swelling
- The
Interflex Washout Units are compatible with
all alternative solvents
- Low
solvent consumption: Approximately ¾ of
a gallon per 30: x 40: of .067” thick
photopolymer, a savings of up to 50% over
other washout systems
- Environmentally
Friendly: Interflex Washout Unit is enclosed
to prevent solvent loss due to evaporation
|
- Operator
Friendly: Virtually no order; one touch operations;
eliminates the use of expensive lint free
towels
- Exceptionally
fast washouts mean minimal plate swelling,
short dry times and higher productivity
- Self-cleaning
design
- Designed
with the highest quality brushes; Limited
lifetime warranty
- Clamp
Free: Allow for maximum plate usage
- Versatile:
Capable of washing multiple plate thickness
simultaneously
- The
Interflex Washout Units produces touch-dry
flexograpic photopolymer plates
|
|
Technical
Details / Interflex
Washout Units
|
|
Model
|
Maximum
Plate Size
|
Dimensions
(H x W x D)
|
Weight
|
Votage
|
|
|
(inches)
|
(mm)
|
(inches)
|
(cm)
|
(lbs)
|
(kgs)
|
(standard)
|
|
IFW
5/80
|
25" x
31.5"
|
635
x 800
|
61" x
128" x 50"
|
155
x 325 x 125
|
2028
|
920
|
380
V / 2.2 Kw
|
|
IFW
9/13
|
35.5" x
51"
|
900
x 1300
|
63" x
161" x 60"
|
160
x 407 x 151
|
2822
|
1280
|
380
V / 4.0 Kw
|
|
IFW
12/20
|
48" x
78.75"
|
1220
x 2000
|
63" x
217" x 60"
|
160
x 551 x 151
|
4365
|
1980
|
380
V / 6.0 Kw
|
|
IFW
13/21
|
50" x
80"
|
1270
x 2032
|
69" x
237" x 74"
|
174
x 601 x 188
|
4850
|
2200
|
380
V / 6.0 Kw
|
|
|
 |
Interflex
Exposure Units
|
Features
Short
Exposures, High Productivity
Interflex
Exposure Units are specifically designed to expose photopolymer
printing plates. Therefore
reflection lamps (tubes) have been chosen with a wavelength
of 365Nm (UVA type), resulting in a powerful and fast
exposure. These lamps are fitted with electronic
starters, thus no pre-exposure warm up is required and
long life is guaranteed.
Interflex Exposure Units operate
at an optimum working temperature of 104° - 122° F
(40° - 50° C). Interflex Exposure Units
are outfitted with circulation fans to avoid overheating
during exposure, which could cause surface damage and
flawed exposures. The number and size of these
circulation fans are determined by the distance from
lamp to plate and the intensity of the UVA lamps.
Complete
Equipment
Interflex Exposure Units
are fitted with maintenance-free vacuum pumps
and filters, reflection-free vacuum tables,
yellow interior lights, hour counters and two
timers. All of the Interflex
Exposure Units can be upgraded with a light
integration system. Each model has 2
drawers below the exposure unit, ample for
the safe storage of the photopolymer plates. Model
IFE 5 / 80 has a manual hood closing and raising
system; the three larger models have automatic
hood closing and raising and are preset amid
your required exposure cycle.
Technical
Details / Interflex Washout Units
|
|
Model
|
Maximum
Plate Size
|
Dimensions
(H x W x D)
|
Weight
|
Votage
|
|
|
(inches)
|
(mm)
|
(inches)
|
(cm)
|
(lbs)
|
(kgs)
|
(standard)
|
|
IFE
5/80
|
24" x
31"
|
550
x 800
|
43" x
51" x 64"
|
108
x 129 x 161
|
573
|
260
|
380
V / 2.8 Kw
|
|
IFE
9/13
|
35" x
51"
|
900
x 1300
|
44" x
67" x 61"
|
110
X 169 x 155
|
965
|
438
|
380
V / 4.7 Kw
|
|
IFE
12/16
|
42" x
60"
|
1067
x 1524
|
45" x
76" x 76"
|
112
x 193 x 191
|
1147
|
523
|
380
V / 5.3 Kw
|
|
IFE
12/20
|
48" x
79"
|
1220
x 2000
|
45" x
91" x 91"
|
112
x 230 x 230
|
1654
|
750
|
380
V / 5.5 Kw
|
|
|
|
|
Features
Safe
and Secure Drying
Interflex
Drying Units have been designed for dyring
water and solvent washable photopolymer plates. Each unit utilizes
forced hot air, an air circulation filter and
is controlled with and LCD thermostatic control. Built-in,
high out put circulation fans an even temperature
throughout the overall dryer.The
Interflex Drying Units have been designed to
be over pressurized to force evaporated fumes
into the exhaust system. Each drying
drawer has a unique twist lock knob and is hermetically
sealed to prevent undesirable solvent fumes from
leaking into the prepress area. Whenever
a drying drawer is opened; the circulation fans
are programmed to shut down automatically, while
the ventilation continues to exhaust the fumes. In
addition, each drying drawer is equipped with up
to 2 programmable LCD timers. Now its easy
to control your drying time for each individual
plate. Interflex Drying Units are capable
of maintaining a temperature of 194° F / 90° C. |
Technical
Details / Interflex Drying Units
|
|
Model
|
Maximum
Plate Size
|
Dimensions
(H x W x D)
|
Weight
|
Votage
|
|
|
(inches)
|
(mm)
|
(inches)
|
(cm)
|
(lbs)
|
(kgs)
|
(standard)
|
|
IFD 5/80
|
25" x 31.5
|
635 x 800
|
31" x 52" x
48"
|
78 x 130 x 120
|
618
|
280
|
380 V / 4.2 Kw
|
|
IFD 9/13.1
|
35.5" x 51"
|
900 x 1300
|
36" x 76" x
50"
|
90 x 193 x 126
|
794
|
360
|
380 V / 9.5 Kw
|
|
IFD 9/13.2
|
35" x 60"
|
889 x 1524
|
36" x 87" x
50"
|
90 x 220 x 126
|
904
|
410
|
380 V / 9.5 Kw
|
|
IFD 12/16
|
42" x 60"
|
1067 x 1524
|
39" x 99" x
58"
|
99 x 250 x 147
|
1504
|
682
|
380 V / 11 Kw
|
|
IFD 12/20
|
48" x 78.8"
|
1220 x 2000
|
56" x 119" x
60"
|
140 x 301 x 152
|
2646
|
1200
|
380 V / 16 Kw
|
|
|
|
 |
Interflex
Finishing
|
|
Technical
Details / Interflex Finishing Units
|
|
Model
|
Maximum
Plate Size
|
Dimensions
(H x W x D)
|
Weight
|
Votage
|
|
|
(inches)
|
(mm)
|
(inches)
|
(cm)
|
(lbs)
|
(kgs)
|
(standard)
|
|
IF PF-PE 5/80
|
25" x 31.5"
|
635 x 800
|
13" x 52" x
48"
|
33 x 130 x 120
|
253
|
110
|
380 V / 3.0 Kw
|
|
IF PF-PE 9/13
|
35.5" x 51"
|
900 x 1300
|
12" x 76" x
50"
|
30 x 193 x 126
|
496
|
225
|
380 V / 6.6 Kw
|
|
IF PF-PE 12/16
|
42" x 60"
|
1067 x 1524
|
14" x 99" x
58"
|
35 x 250 x 147
|
1032
|
468
|
380 V / 7.6 Kw
|
|
IF PF-PE 12/20
|
48" x 78.8"
|
1220 x 2000
|
14" x 119" x
56"
|
35 x 301 x 141
|
1191
|
540
|
380 V / 10.0 Kw
|
|
|
|
 |
IDI
Advantage
|
|
Features
The plate is exposed using a principle
that differs from conventional techniques. The
UV source is a point light lamp. Light
is guided to the plate using special reflectors
and has an adjustable output. The main
exposure is conducted automatically in 2 consecutive
steps. The initial exposure with a non-scattering
point light source creates sharply defined lines
and dots without shoulders. This image
produced in this step is optimum, but is without
the necessary shoulders. The 2nd step of
main exposure is carried out using a filter. This
filter scatters the light as in conventional
units and produces the needed shoulder. |
Technical
Details / Interflex Exposure Units
|
|
Model
|
Maximum
Plate Size
|
Dimensions
(H x W x D)
|
Weight
|
Votage
|
|
|
(inches)
|
(mm)
|
(inches)
|
(cm)
|
(lbs)
|
(kgs)
|
(standard)
|
|
IDI
33
|
22" x
32"
|
559
x 813
|
89" x
48" x 72"
|
226
x 122 x 183
|
1300
|
589
|
208-240
V / 40 A
|
|
IDI
45
|
35" x
45"
|
889
x 1143
|
95" x
58" x 79"
|
241
x 147 x 201
|
1600
|
726
|
208-240
V / 50 A
|
|
IDI
60
|
48" x
60"
|
1220
X 1524
|
127" x
85" x 89 "
|
323
x 216 x 226
|
2400
|
1089
|
208-240
V / 90 A
|
|
|
|
 |
AZFlexo
Compact 35-50
|
|
Technical Data
|
|
Plate
size:
|
13.75” x 19.5” /
35 x 50 mm |
|
System functions:
|
Back, main, post-exposure with UVC, washout,
drying |
|
Power supply:
|
220V – 2500W (13 Amp) – single
phases – 2.5 Kw |
|
Pipe fittings:
|
Cock with ball valve of 3/8 and 1 |
Exposure: The
drawer is provided with 9 lamps for the main
and post exposure type UV 40 W 10R. The
UVC exposure takes place in a stainless steel
drawer with 10 lamps type TUV 15W. The
microprocessor system keeps an internal memory
of the lamps life to help determine when it’s
time to replace them. The vacuum system
and the vacuum sheet perfectly hold the negative
to the plate. The lamps and the vacuum
surface are cooled by forced air circulation
inside the drawer. If the lid is opened
the exposure is stopped until the lid is closed
again.
Washout: The
stainless steel tank has a capacity of 5.3
gallons / 20 liters approx. The
nylon brushes are assembled on springs to have
an even pressure on plates of various thicknesses. The
washout platen rotates alternatively in two
directions to ensure an even washout of the
plate and it stops if the lid is opened.
Programming: The
microprocessor controlled keyboard allows the
use to set up to nine customized programs to
control the time of each function: back
exposure, main exposure, post-exposure and
UVC, washout and drying. For the last
two functions it is also possible to set the
temperature in °C. Furthermore, the
display shows the value of the vacuum (in Bar)
and the drying time for each drawer.
Green/Red
Warning LEDs constantly informing about the
status of the machine – acoustic
alarm in case of errors and/or malfunctions.
Dryer: The
two drawers are provided with a 1000W heater,
forced air circulation and safety switch.
An exhausting system extracts the
solvent fumes from the washout, the exposure and
the dryer. |
|
|
|
Technical Data
|
|
|
Plate
size:
|
26” x
86” / 660 x 860 mm |
|
System
functions:
|
back,
main, post-exposure with UVC, washout,
drying |
|
Power
supply:
|
220V
- single phases – 4.5 KW
(Upon request: 230V – 3 phases – 20
Amp) |
|
Pipe
fittings:
|
cock
with ball valve of 3/8 and 1 |
| |
|
|
|
Features
|
|
|
Exposure: The
drawer is provided with 13 lamps for the main
exposure type TL 60W 10R (120mm), 7 lamps for
the post-exposure type TL 60W 10R and 6 lamps
for the UVC exposure type TUV 36W. The microprocessor
system keeps an internal memory of the lamps
life to help determine when it’s time
to replace them. The vacuum system and the
vacuum sheet perfectly hold the negative to
the plate. The lamps and the vacuum surface
are cooled by forced air circulation inside
the drawer. If the lid is opened the exposure
is stopped until the lid is closed again.
Washout: the
stainless steel tank has a capacity of 26.4
Gallons / 100 Litres approx. and it is provided
with solvent level indicator. The nylon brushes
are assembled on springs to have an even pressure
on plates of various thicknesses. The washout
platen is movable forward and is provided with
a clamp to hold the plate. It rotates alternatively
in two directions to ensure an even washout
of the plate and it stops if the lid is opened.
If new solvents are used, a coil on the bottom
of the tank can heat them; the computer controls
the temperature of the water running inside
the coil.
Programming: the
microprocessor controlled keyboard allows the
user to set up to nine customized programs
to control the time of each function: back
exposure, main exposure, post-exposure and
UVC, washout and drying. For the last two functions
it is also possible to set the temperature
in °C. Furthermore, the display shows
the value of the vacuum (in Bar) and the drying
time for each drawer.
Green/Red
Warning LEDs constantly informing about the
status of the machine – acoustic alarm
in case of errors and/or malfunctions.
Dryer: the
two drawers are provided with three 500W heaters,
forced air circulation and safety switch.
An
exhausting system extracts the solvent fumes
from the washout, the exposure and the dryer.
|
|
|
|
|
Technical Data
|
Plate
size:
|
39.3” x
51.2” / 1000 x 1300 mm |
|
System
functions:
|
back,
main and post-exposure with UVC, drying |
|
Power
supply:
|
220V
- single phase – 4.5 KW (Upon
request: 230V – 3 phases) |
|
Features
Exposure: The
unit is provided with 21 lamps for the back and
main exposure type TL 80W 10R (150mm). The microprocessor
system keeps an internal memory of the lamps life
to help determine when it’s time to replace
them. The vacuum system and the vacuum sheet perfectly
hold the negative to the plate. The temperature
of the lamps is controlled by forced air circulation
inside the drawer. If the lid is opened the exposure
is stopped until the lid is closed again.
Post-exposure: the
stainless steel drawer is provided with 19
lamps for the post-exposure type TL 60W 10R
and 18 lamps for the UVC exposure type TUV
36W. The microprocessor system keeps an internal
memory of the lamps life to help determine
when it’s time to replace them.
Dryer: an
even temperature in the four drawers is provided
by ET heaters 500W per heater with a safety
switch.
An
exhausting system extracts the solvent fumes
from the exposure and the dryer.
Programming: the
microprocessor controlled keyboard allows the
user to set up to nine customized programs
to control the time of each function: back
exposure, main exposure, post-exposure and
UVC, and the temperature of the dryer. Furthermore,
the display shows the value of the vacuum (in
Bar) and the drying time for each drawer.
Green/Red
Warning LEDs constantly informing about the
status of the machine – acoustic alarm
in case of errors and/or malfunctions.
|
|
|
|
|
Features
|
Plate
size:
|
35.4” x
47.25” / 900 x 1200 mm |
|
System
functions:
|
washout
of flexographic plates with solvent |
|
Power
supply:
|
220V
- single phase |
|
Pipe fittings:
|
cock with ball valve of 3/8 and 1 |
Technical Data
Programming: the
microprocessor controlled keyboard allows
the user to set up to nine customized programs
to control the following functions: charge/discharge
of the solvent in the tank, solvent temperature,
water heating, washout time and replacement
of a programmed quantity of used solvent
with new solvent.
Solvent: is
charged by mean of a pump with level sensor.
Washout: the
stainless steel tank has a capacity of 52.8
Gallons / 200 litres approx. and it is provided
with solvent level indicator. The nylon brushes
are assembled on an adjustable support to suit
plates of various thicknesses. The washout
platen is movable forward, is provided with
a clamp to hold the plate. It rotates alternatively
in two directions to ensure an even washout
of the plate and it stops if the lid is opened.
If new solvents are used, a coil on the bottom
of the tank can heat them; the computer controls
the temperature of the water running inside
the coil.
An
exhausting system extracts the solvent fumes
Green/Red
Warning LEDs constantly informing about the
status of the machine – acoustic alarm
in case of errors and/or malfunctions
|
| |
The
Jet Clean 800 is the most efficient, user friendly, automated
plate cleaner in the market today.
With the Jet Clean 800 Cleaner, you can completely
clean any type of dirty printing plates. The
Jet Clean 800 Plate Cleaner features a compact “In-Line” design
that flushes, brushes and dries the plates, resulting
in a completely clean plate surface. The
Jet clean 800 utilizes a unique sticky plate carrier
system, manufactured by Polymount International, B.V.
called; Twinlock™ Carrier sheets hold the dirty
plates firmly in place during the cleaning process.
The
Jet Clean routinely completes a cleaning cycle of 1500
sq. in. every 5 minutes and the plates can be stored
immediately. There is no additional drying time
required.
Imagine, just press a button and your dirty plates are cleaned effortlessly and automatically.
How efficient is it?
The
Jet Clean 800 can clean 6 to 8 times more plates
than cleaning them by hand. The Jet Clean 800
Plate Cleaner encloses a tank holding 33 gallons
of Jet Wash water-based cleaner. Jet Wash Solution
is a detergent that is constanly recyled in a closed
circuation system. A unique combination of
filters and a cascading system in the tank ensures
that the cleanest solution is always used for washing
the plates. It enables the operator to clean
largte quantities of printing plates effortlessly. Each
tank full of Jet Wash Solution is capable of washing
up to 1.5 million square inches of dirty plates.
Technical Details |
Model
|
Maximum size
|
Dimensions (HxW.D)
|
Weight
|
Voltage
|
|
(inches) |
(mm) |
(inches) |
(mm) |
(lbs) |
(kgs) |
(standard) |
JetClean 800 |
31.5" x 49.2" |
800 x 1250 |
50 x 101" x 51" |
125 x 255 x 128 |
660 |
300 |
208 Volt / 3 ph |
|
|
|
|
